Page 1 of 2
Plesk 8.3 latest on CentOS 5.1 install error :(
Posted: Thu Apr 24, 2008 9:06 am
by laughingbuddha
Just tried to install Plesk 8.3 on CentOS 5.1 and it failed on:-
Packages "httpd-2.2.3-11.el5_1.centos.3.i386" and httpd-2.2.2-11.el5.centos.i386" cannot be installed at the same time
bcause of the conflict on the file "/etc/httpd/conf.d/README"
Help!
It's a clean install on a clean server hanging off my Netgear DG834N router. I have opened all access to the local IP that the server (only for the install and setup) is set to, and have also done what is needed in the config files for it to see the outside world and resolve to it's name being s1.youandtheweb.co.uk
Please help!
Matt
Posted: Thu Apr 24, 2008 9:14 am
by Highland
Did you update any packages after installing Centos? The cardinal rule in Plesk installs: never update packages until AFTER you install Plesk. Plesk expects a base install and will go nuts if it doesn't get it.
Posted: Thu Apr 24, 2008 9:17 am
by laughingbuddha
Nope. Totaly clean install.
Matt
Posted: Thu Apr 24, 2008 10:06 am
by scott
Try installing it through yum, the autoinstaller doesn't really leverage packaging like yum does. Its always behind on things.
Posted: Thu Apr 24, 2008 11:21 am
by laughingbuddha
Is that easier. When I purchase my licence, I'm not planning on using all the features.
what command line do I use for a yum install? and will it install stuff like FastCGI and ASP, not that I've used it, but features might be good for clients personaly I'm a PHP and MySQL man myself.
Matt
Posted: Thu Apr 24, 2008 11:24 am
by scott
wget -q -O -
http://www.atomicorp.com/installers/atomic |sh
Hit "y" when it asks if you want to enable the plesk repo.
Posted: Thu Apr 24, 2008 1:47 pm
by laughingbuddha
I get the following error when executing that command:-
sh: line 1: wget:: command not found
sh: line 2: Usage:: command not found
sh: line 4: unexpected EOF while looking for matching `''
sh: line 5: syntax error: unexpected end of file
?
Posted: Thu Apr 24, 2008 4:19 pm
by laughingbuddha
Don't worry, I'm blond. Found the issue, needless to user it was an input error by the user......doh!
Once I have run that command, I guess I would then run yum update
Well I hope so, because that's what I just did
Matt
Posted: Thu Apr 24, 2008 4:33 pm
by scott
Sounds like someone broke your VPS. I would complain to them about it
Posted: Thu Apr 24, 2008 4:34 pm
by laughingbuddha
Not on a VPS, HP ProLiant DL360 G3
Well I did the yum update, rebooted and no Plesk still. Hummm
Posted: Fri Apr 25, 2008 9:14 am
by laughingbuddha
Ok, so once it's downloaded and everything how do I actualy install it?
Matt
Posted: Fri Apr 25, 2008 9:26 am
by scott
For a minimal install:
yum install psa
For just about everything:
yum install psa*
Posted: Fri Apr 25, 2008 9:31 am
by laughingbuddha
Wicked, nice one. Cheers my man
I guess your version installs SSO like the other one does.
I might just go for a full install, and remove what I don't want afterwards. I can do that can't I?
Matt
Posted: Fri Apr 25, 2008 10:10 am
by laughingbuddha
Just went for the full install. Has that got the SSO that Swsoft put into Plesk 8.3?
Also, how much is a subscription to ASL channel? Wanna make sure my server is secure.
Matt
Posted: Fri Apr 25, 2008 12:54 pm
by breun
laughingbuddha wrote:I guess your version installs SSO like the other one does.
It's not another version, it's the exact same packages.
I might just go for a full install, and remove what I don't want afterwards. I can do that can't I?
It's a lot easier to do a minimal install and add stuff later.